Amsoil vs Mobil 1 Royal Purple Castrol Valvoline
Amsoil API Motor Oil comparisonTesting
Amsoil Synthetic 10W-30 Motor Oil (ATM) and 10 competing conventional and synthetic 10W-30 motor oils were
subjected to a series of API motor oil tests. The competing oils included petroleum-based Castrol GTX Drive Hard,
Mobil Drive Clean, Pennzoil with Purebase, Quaker State Peak Performance and Valvoline, as well as synthetic-based
Valvoline Synpower, Quaker State, Castrol Syntec, Pennzoil and Mobil 1 SuperSyn Multi-Vehicle.
Seven API tests were run on the motor oils. The Thin-Film Oxygen Uptake Test (TFOUT) measures the oxidation
stability of engine oils. The High Temperature/High Shear Test (HTHS) measures a lubricant’s viscosity under severe
operating conditions. The NOACK Volatility Test measures the evaporation loss of oils in high temperature service.
Pour Point indicates the lowest temperature at which a fluid will flow. Total Base Number (TBN) is the measurement
of a lubricant’s reserve alkalinity for combating acids. The Cold Cranking Simulator Test (CCS) measures a
lubricant’s viscosity at low temperatures and high shear rates. The Four-Ball Wear Test measures a lubricant’s wear
protection properties. The impressive test results show Amsoil Synthetic 10W-30 Motor Oil outperformed the
competitors in each test.
Thin-Film Oxygen Uptake (ASTM D-4742)
The Thin-Film Oxygen Uptake Test evaluates the oxidation stability of lubricating oils. A mixture of the test
oil and chemistries found in gasoline engine operation (oxidized/nitrated fuel, soluble metals and distilled water)
are placed in a test vessel, which is pressurized with oxygen and placed in a heated bath. Anti-oxidant breakdown
is evident when the oxygen pressure in the vessel rapidly decreases. At this point, the induction time (break
point) of the oil is recorded. As shown in the graph, Amsoil Synthetic 10W-30 Motor Oil had the highest induction
time of all the tested oils. In fact, it didn’t reach its break point in over 500 minutes of testing.
The superior oxidation stability of Amsoil Synthetic 10W-30 Motor Oil allows it to effectively resist the formation
of engine deposits and sludge, keeping engines running clean and efficient and extending oil life. It also resists
thickening, maintaining its superior wear protection and lubricating properties and maximizing fuel efficiency.
High Temperature/High Shear (ASTM D-4683):
The High Temperature/High Shear Test measures a lubricant’s viscosity under severe high temperature and shear
conditions that resemble highly-loaded journal bearings in fired internal combustion engines. In order to prevent
bearing wear, it is important for a lubricant to maintain its protective viscosity under severe operating
conditions. The minimum High Temperature/High Shear viscosity for a 30 weight oil is 2.9 cP. As shown in the graph,
Amsoil Synthetic 10W-30 Motor Oil surpasses this minimum standard and displayed the highest High Temperature/High
Shear viscosity in the group.
The superior viscosity retention of Amsoil Synthetic 10W-30 Motor Oil in the face of severe temperature and shear
conditions allows it to provide continuous, unsurpassed protection for engine bearings, extending equipment life
and preventing wear.
NOACK Volatility (ASTM D-5800):
The NOACK Volatility Test determines the evaporation loss of lubricants in high temperature service.The more motor
oils vaporize, the thicker and heavier they become, contributing to poor circulation, reduced fuel economy and
increased oil consumption, wear and emissions. A maximum of 15 percent evaporation loss is allowable to meet API SL
and ILSAC GF-3 specifications. As shown in the graph, Amsoil Synthetic 10W-30 Motor Oil outperformed its nearest
competitor by over 30 percent.
The extremely low volatility of Amsoil Synthetic 10W-30 Motor Oil allows it to maintain its superior protective and
performance qualities throughout extended drain intervals, even when faced with severe operating temperatures. In
addition, oil consumption and emissions are minimized and fuel efficiency is maximized.
Pour Point (ASTM D-97):
The Pour Point Test determines the lowest temperature at which a lubricant will flow when cooled under prescribed
conditions. The lower a lubricant’s pour point, the better protection it provides in low temperature service. As
shown in the graph, Amsoil Synthetic 10W-30 Motor Oil has the lowest pour point of the tested oils.
The low pour point of Amsoil Synthetic 10W-30 Motor Oil allows it to maintain its fluidity in extremely low
temperatures, reducing drag on moving vehicle parts, providing critical engine components with quick, essential
lubrication and easing startup in cold temperatures. Wear is greatly reduced and equipment life is extended.
Total Base Number (ASTM D-2896):
Total Base Number (TBN) is the measurement of a lubricant’s reserve alkalinity, which aids in the control of acids
formed during the combustion process. The higher a motor oil’s TBN, the more effective it is in suspending
wear-causing contaminants and reducing the corrosive effects of acids over an extended period of time. As shown in
the graph, Amsoil Synthetic 10W-30 Motor Oil has the highest TBN of the tested oils.
The high TBN of Amsoil Synthetic 10W-30 Motor Oil allows it to effectively combat wear-causing contaminants and
acids, providing superior protection and performance over extended drain intervals.
Cold Crank Simulator (ASTM D-5293):
The Cold Crank Simulator Test determines the apparent viscosity of lubricants at low temperatures and high shear
rates. Viscosity of lubricants under these conditions is directly related to engine cranking and startability. The
lower a lubricant’s cold crank viscosity, the easier an engine will turn over in cold temperatures. 10W motor oils
are tested at -25°C and must have a viscosity below 7000 cP to pass. As shown in the graph, Amsoil Synthetic 10W-30
Motor Oil is well below the maximum requirement, while many of the competing oils barely pass.
The low cold crank viscosity of Amsoil Synthetic 10W-30 Motor Oil reduces drag on moving engine parts and allows
engines to achieve critical cranking speed in extremely frigid temperatures. Engines turn over quickly and
dependably in the coldest winter temperatures.
Four Ball Wear (ASTM D-4172):
The Four Ball Wear Test determines the wear protection properties of a lubricant. Three metal balls are clamped
together and covered with the test lubricant, while a rotating fourth ball is pressed against them in sliding
contact. This contact typically produces a wear scar, which is measured and recorded. The smaller the average wear
scar, the better the wear protection provided by the lubricant. As shown in the graph, Amsoil Synthetic 10W-30
Motor Oil produced the smallest wear scar of the tested lubricants.
Amsoil Synthetic 10W-30 Motor Oil provides unsurpassed protection against engine wear. Equipment life is extended,
and repairs, downtime and expenses are reduced.
Amsoil INC. has been the leader in synthetic motor oil formulation since its introduction of the world’s first
API rated synthetic motor oil in 1972. By specializing exclusively in synthetic lubricant technology, Amsoil is
able to optimize the most advanced chemistries available. The “Genuine Synthetic PAO Formulated” designation
displayed on Amsoil packaging indicates that the oils are formulated with Polyalphaolefin (PAO) synthetic base
stocks. This chemistry is the industry’s premier base stock technology. Unlike conventional mineral-based
chemistries, Amsoil PAO base stocks contain fully saturated, hydrogenated molecules and are free of wax and other
impurities. Combined with an exact balance of premium additives, it delivers superior hot and cold temperature
performance, resists oxidation and acid formation and provides long-term wear protection. Amsoil “Genuine Synthetic
PAO Formulated” oils have shattered the parameters of the most rigorous industry testing and set the standard for
all other motor oils.
Royal Purple Info
As you may know, Royal Purple is well known in racing circles. The chemistry they use is something Amsoil, Inc.
chooses not to use in their oil formulation. One of Amsoil's big selling points is extended drain intervals, such
as our 25,000 mile and 25k mile oil change intervals. Some additive chemicals such as Moly may cause adverse
conditions when used for long periods.
Royal Purple uses a different chemistry than most oil producers. They are one of only a handful of marketers
using Molybdenum Disulfide (Moly) in their oil formulations at these higher levels.
Moly is a processed mineral that is similar in appearance to graphite. Moly has good lubricating properties when
used either by itself (in dry power form or as an additive to oil or other lubricants). Particles of the Moly can
come out of suspension and agglomerate. Over time this may actually clog or partially clog oil filters or oil lines
and the remainder normally settles in the bottom of the oil pan. This seems to be more likely when using extended
drain intervals. The only test we ran on Royal Purple involved their 20W50 Racing oil versus our Amsoil Series 2000
Synthetic 20W50 Racing Oil (TRO). We ran two 4 ball wear tests with different parameters, a spectrographic
baseline, FTIR scan and volatility tests. The Royal Purple showed a significantly high volatility rate with a
12.51% boil off rate. This compares to the Amsoil TRO with only a 4.47% volatility rating. Wear scars were also
smaller with the TRO. For example the Amsoil TRO left a .41mm scar and the Royal Purple oil left a .66mm scar. The
lower the scar damage number the better! There was also a surprising difference in the viscosity index. The RP has
a VI of 129 versus 155 for the TRO. The higher the VI, the better the viscosity stays in place at high
Note: This information was provided by Amsoil, Inc. Tech Department. An independent lab tested the Royal Purple
20W-50 racing oil against the Amsoil 20W-50 racing oil. The results are posted above. Test results found Moly in
the Royal Purple oil sample.
6 Month Amsoil Preferred Customer
Trial Membership Form
Register for trial Now and Save 25%-30% off Retail Prices
Please contact us with any questions regarding the Dealership and Preferred Customer option and we can explain them
both in more detail and also answer any of your product or technical questions. Thank you for your interest in
Amsoil products and for confidence in our technical and business expertise. Amsoil is our business and our passion
and it is our goal to ensure your complete satisfaction. If you would like the Trial
Membership, fill out the form below. Takes about 24hrs for your personal account number to be processed and
sent to you via email.
The information you place on this form will never be sold or used in a
manner other than this preferred customer program submission form and to send the information to
OOPS! You forgot to upload swfobject.js ! You must upload this file for your form to work.